132
D-108 Owner’s Manual (MIDI Implementation Chart/MMC List)
Explanation on the Command/Mode Set
12 22 (<on/off>): loop on/off command
The command for setting the "loop mode on/off" (=ON/OFF of
AUTO RTN) of D-108. Default figure of the loop operation
mode is "12=stop" and this cannot be changed.
12 28 (<post locate mode>): post locate command
The command for setting the "post locate mode" (=ON/OFF of
AUTO PLAY) of D-108.It will stop after locating if "post locate
mode=12." It will enter play after locating if "post locate
mode=15."
12 2D (<on/off>): auto rec command
The command for setting "auto rec mode on/off" (=ON/OFF of
AUTO PUNCH) of D-108. Upon receiving this command, D-
160 will immediately reply the operating condition by sending
"32 2D (<edit message>)".
12 41 (<lock enable>): lock enable command
The command for setting "slave mode on/off" (setup menu) of
D-108.
12 42 (<lock mode>): lock mode command
The command for setup of the slave mode (setup menu) when
this equipment is set to "slave mode on."
12 45 (<count><mmc track>) : copy clip command
When this command is received, D-108 will copy (multiple num-
ber of tracks can be copied simultaneously) the sound data, as
data for copy paste, from the pre-registered clipboard-in point
to the clipboard-out point in the track specified by <mmc track>.
With completion of copying the data into the clipboard, D-108
will immediately reply with "32 45 (<edit message=01 (com-
pleted)>)". If copy cannot be executed due to improper fig-
ures of the pre-registered clipboard in/clipboard out points or
incorrect track section, the corresponding <edit message> will
be returned.
12 46 (<count=01><repeat count>): copy paste command
12 46 (<count><repeat count><mmc track>): copy paste com-
mand
When this command is received, D-108 will paste the sound
data which has been copied into the clipboard, on the same
track from the pre-registered auto punch in point as the start-
ing point for the number of time specified by <repeat count>.
However, if the sound data length in the clipboard is less than
10ms, the specifying the <repeat count> will be limited to
"01." Also, by specifying <mmc track>, paste can be executed
on other tracks in mono (in one track units) or stereo units (in
combinations of tracks 1-2, 3-4, 5-6, 7-8).
Since time corresponding to length of the copy clipped sound
data is required to complete the copy paste operation, D-108
immediately replies with "32 46(<edit message=02 (active)>)"
after receiving the command.
Successively upon completing the paste operation, "32 46 (<edit
message=01(completed)>)" is transmitted.
If paste cannot be executed due to improper figures of the pre-
registered auto punch in point, insufficient disc capacity, no
sound data in the clipboard, etc., the corresponding <edit mes-
sage> will be replied.
12 47 (<count><mmc track>): erase command
When this command is received, D-108 will erase the data
(writes in "0" data) in the section from the pre-registered auto
punch in point through auto punch out point in the track speci-
fied by <mmc track>. Since time corresponding to length of
the erase section is required to complete the erase operation,
D-108 will immediately reply by "32 47 (<edit message=02
(active)>)" after receiving the command.
After the completion of erase operation, "32 47 (<edit mes-
sage=01 (completed)>)" will be transmitted.
If erase cannot be executed due to improper figures of the pre-
registered auto punch in point/auto punch out point, incor-
rect track section, etc., the corresponding <edit message> will
be replied.
12 49: clipboard play command
When this command is received, D-108 will playback once from
the head of the sound data copied in the clipboard by the copy
clip and move clip commands.
Immediately after receiving the command, D-108 will reply
with "32 49 (<edit message=02 (active)><count><mmc track>)."
The sound data track number is indicated by (mmc track>.
Upon completion of playback, "32 49 (<edit message=01 (com-
pleted) is sent and clipboard play is ended. If there is no sound
data in the clipboard, "32 49 (<edit message=14 (void data)>)"
will be sent and clipboard play operation will be interrupted.
12 4A: undo command
Upon receiving this command, D-108 will revert to the condi-
tion prior to editing copy paste,erase, move paste, cut, redo
operation. With completion of undo operation, D-108 will re-
ply with "32 4A (<edit message=01(completed)>)."
If D-108 is not possible to undo, "32 4A (<edit message=00 (no
message)>)" will be replied.
12 4B: redo command
When this command is received, D-108 will return to the con-
dition prior to undo operation.
With completion of redo operation, D-108 will reply with "32
4B (<edit message=01(completed)>)."
If D-108 is not possible to redo, "32 4B (<edit message=00 (no
message)>)" will be replied.
12 4D (<count><mmc track>): move clip command
When this command is received, D-108 will copy (multiple
tracks can be copied simultaneously) the sound data from the
pre-registered clipboard in point to the clipboard out point, as
data for move paste operation. With completion copying the
data into the clipboard, D-108 will immediately reply with "32
4D (<edit message=01 (completed)>)." If copy cannot be ex-
ecuted by the reason of pre-registered improper clipboard in/
clipboard out point figures or incorrect track section, etc., the
corresponding <edit message> will be replied.
12 4E (<count=01><repeat count>): move paste command
12 4E (<count><repeat count><mmc track>): move paste com-
mand
When this command is received, D-108 will paste the sound
data which have been move clipped in the clipboard, for the
number of times specified by <repeat count> on the same track
from the pre-registered auto punch in point as the starting
point. At the same time, the move clipped original sound data
Terms of Use | Privacy Policy | DMCA Policy
2006-2022 Rsmanuals.com