112
D-108 Owner’s Manual (Changing the initial setting <SETUP mode>)
1. Press the DISP SEL key and choose the flashing SETUP mode
on the display. Then, press the EXECUTE/YES key.
The SETUP display will stop flashing.
2. With the JOG dial, choose “Preroll Time?”.
The “?” display will start flashing. The display will also show
the current setting. In the case of initial setting, it will show
00 second.
3. Press the EXECUTE/YES key.
The current setting will start flashing “**” which indicates it
is ready to change setting.
4. With the JOG dial, enter the required preroll time.
You can set the preroll time between 0 and 10 sec in 1
second steps. If you turn the JOG dial clockwise, the time
value will increase. And if you turn the JOG dial counter
clockwise, the time value will decrease vise versa.
5. Press the EXECUTE/YES key after you have entered the
preroll time you want.
The setting will be registered and the display will go back to
the Item 2 above.
44.1kHz
SETUP
87654321
42
OL
0
30
24
18
12
9
6
3
* Press either the “STOP” button or EXIT/NO key to re-
turn from the second step menu to the first or to quit
the SETUP mode. The menu will go backwards each time
you press either key so that you can correct the setting,
choose some other SETUP mode or eventually return to
the normal time base display.
MIDI Sync Signal Output Setting ("Midi Sync Out ? ")
This mode sets up the type of MIDI sync signal for external MIDI equipment.
The type of signal the D-108 outputs is either MIDI Clock & Song Position Pointer or MTC (MIDI Time Code). Choose one so that the
external MIDI equipment can recognize it when synchronizing to the D-108. In case of the MIDI Clock & Song Position Pointer, you
need to set the section "Time Signature" and section "Tempo as previously mentioned."
In case of the MTC ( MIDI Time Code), you need to set the section "MTC Frame Rate", "MTC Offset Time" and " MTC Offset Mode"
described below.
* See page "75" “MIDI Synchronization Function” for details of the MIDI sync.
* Initial setting : CLK
* Available setting : CLK (MIDI Clock & Song Position Pointer), MTC (MIDI Time Code), Off
* This setting is applicable song by song.
* This setting can be saved or loaded as a part of the song data.
* The setting is memorized even when the power is off.
* Make sure to choose the right program before setting up this mode.
1. Press the DISP SEL key and choose the flashing SETUP mode
on the display. Then, press the EXECUTE/YES key.
The SETUP display will stop flashing.
2. With the JOG dial, choose “Midi Sync Out?”.
The “?” display will start flashing. The display will also show
the current setting. In the case of initial setting, it will show
CLK.
3. Press the EXECUTE/YES key.
The current setting will start flashing “**” which indicates it
is ready to change setting.
4. With the JOG dial, enter a required Midi Sync Signal.
Choose the type of MIDI signal you want.
* Press either the “STOP” button or EXIT/NO key to re-
turn from the second step menu to the first or to quit
SETUP mode. The menu will go backwards each time you
press either key so that you can correct the setting, choose
some other SETUP mode or eventually return to the nor-
mal time base display.
5. Press the EXECUTE/YES key after you have entered the
Midi Sync Signal you wanted.
The setting will be registered and the display will go back to
step 2 above.
“CLK” The D-108 generates the MIDI Clock & Song
Position Pointer.
“MTC” The D-108 generates the MIDI Time Code.
“Off” The D-108 generates no MIDI Sync signal.
44.1kHz
SETUP
87654321
42
OL
0
30
24
18
12
9
6
3
44.1kHz
SETUP
87654321
42
OL
0
30
24
18
12
9
6
3
44.1kHz
SETUP
87654321
42
OL
0
30
24
18
12
9
6
3
Terms of Use | Privacy Policy | DMCA Policy
2006-2022 Rsmanuals.com