Loading...
E-9E-8
English
basic
operation
e CDS27 is supplied with the CR902 remote control.
Using the remote control
Please keep in mind the following when using the
remote control:
< Ensure there are no obstacles between the
remote control and the remote sensor on the
front panel. e remote has a range of about
7metres. (If the remote sensor is obscured, the
IR in remote control input jack on the rear panel
is available. Please consult your dealer for further
information.)
< Remote operation may become unreliable if
strong sunlight or uorescent light is shining on
the remote sensor of the unit.
< Replace the batteries when you notice a
reduction in the operating range of the remote
control.
Inserting batteries into the remote control
1. Open the battery compartment on the back of
the handset.
2. Insert two ‘AAA’ batteries according to the
diagram on the battery cover casing.
3. Slide the battery cover casing back into position
and lock it closed with a click.
remote
control
NOTE
< Incorrect use of batteries can result in hazards
such as leakage and bursting.
< Do not mix old and new batteries together.
< Do not use non-identical batteries together
– although they may look similar, dierent
batteries may have dierent voltages.
< Ensure the plus (+) and minus (–) ends of
each battery match the indications in the
battery compartment.
< Remove batteries from equipment that is not
going to be used for a month or more.
< When disposing of used batteries, please
comply with governmental or local
regulations that apply in your country or area.
The CR902 remote complies with Part 15
of the FCC rules
is equipment has been tested and found to comply
with the limits for a class B digital device, pursuant
to part 15 of the FCC Rules. ese limits are
designed to provide a reasonable protection against
harmful interference in a residential installation.
is equipment generates, uses, and can radiated
radio frequency energy and if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment o and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet or a circuit
dierent from that to which the receiver is
connected.
Consult the dealer or an experienced audio
technician for help.
AUDIO
SACD
MENU
FM MONO P/TUNE STORE
INFO
BD
CR902
RTN
During playback
Scan
Press 8 or 7 on the front-panel or remote control
to scan forwards or backwards, at x4 normal playback
speed. To resume normal playback, press PLAY.
Skipping chapters/tracks
To skip tracks, press /or 0.
When skipping back, the rst button press takes you to
the beginning of the current track. Pressing the button
again takes you to the start of the previous track.
Pausing playback
Press 4/; on the front panel or ; on the remote
control to pause playback. To resume playback, press
4/; on the front panel or 4 on the handset.
Stopping playback
Press the </1 button on the front panel or < on the
remote control to stop playback.
Introduction
‘Basic operation’ explains how to play audio discs,
network content and audio les stored on USB media.
Note that it may be necessary to congure your player
correctly for your system before optimum – or any–
playback can be achieved. Player conguration is
described beginning on page 11.
Switching on
Switch the unit on by pressing the POWER button. e
status LED glows green when the unit is powered up
and red when in standby mode. Standby mode may be
entered using the standby button on the remote control
and exited using either the same button, or the </1
key on the front panel. If the POWER button is pressed
(or power is removed) whilst in standby, the unit will
enter standby mode when power is re-applied.
Note that the remote control sensor is located to the
right-hand side of the display window. Do not obstruct
this or the remote control will not work.
Playing a disc
Press </1 on the front panel (or 1 on the handset)
and place the disc on the tray, with the playback side
facing down (some discs are double sided, in which
case the side labelled ‘side A’ should face up to play
sideA).
Press </1 on the front panel to close the tray. e disc
loads aer a pause of a few seconds.
A disc may take some time to load once the tray is
closed. When the ‘Disc Autoplay’ setting is set to On
(the default setting), playback starts automatically. (For
details, refer to ‘Disc Auto Playback’ on page 11).
For discs that do not play automatically, press 4/; on
the front panel or press 4 on the remote control.
Playing from the network
Ensure the CDS27 is connected to your local network.
Select ‘Media Browser’ from the home screen, the user
will be presented with a list of devices available for
browsing. Navigate the available libraries using the
',<> keys on the remote.
Network music playback may also ne controlled from
your computer, phone or mobile device using your
favourite UPnP control point application.
Pressing OK or 4 on a highlighted audio le will access
the le for playback. Playback will continue through all
subsequent tracks in the playback directory.
Playing from USB
Connect your USB device to the USB socket to the rear
of the CDS27. Aer the device has been recognised
select ‘Media Browser’ from the home screen, then
choose the ‘USB’ option from the media list.
Navigate directions using the ',<> keys on
the remote and begin playback of a highlighted audio
le by pressing OK, 4or >. Playback will continue
through all subsequent tracks in the playback directory.
Loading...
Terms of Use | Privacy Policy | DMCA Policy
2006-2020 Rsmanuals.com