Loading...
16
.
CAUTION
1. All cleaning and maintenance should be done when
grill is cool and with the fuel supply disconnected.
2. Do NOT clean any grill part in a self-cleaning oven.
The extreme heat will damage the finish.
3. Do NOT enlarge valve orifices or burner ports when
cleaning the valves or burners.
4. Unplug rotisserie motor from the outlet when not in
use and before cleaning. Allow to cool before putting
on or taking off parts.
.
1. This grill should be thoroughly cleaned and
inspected on a regular basis.
2. Abrasive cleaners will damage this product.
3. Never use oven cleaner to clean any part of grill.
NOTICE
Cleaning and Care
Operating Instructions (continued)
WWARNING: OUTDOOR USE ONLY. DO NOT EXPOSE TO RAIN.
Attaching Meat
1. Attach rotisserie motor per “Assembly Instructions – Rotisserie” section.
2. Attach rotisserie counterweight and handle to rotisserie rod (Figure 10).
3. Slide one rotisserie fork onto rod (Figure 11).
4. Push rotisserie rod through the middle of the meat and evenly attach to the prongs of the rotisserie fork (Figure 12).
5. Attach second rotisserie fork onto rod and insert prongs into meat. Tighten rotisserie forks (Figure 13).
6. Insert rotisserie rod into motor and place other end of rod into grooves on bottom bowl (Figures 14 and 15).
7. Turn rotisserie motor “ON” to test meat placement.
Note: Heavy side of meat should rotate down towards the bottom bowl. Adjust counterweight if needed for a proper balance. If meat still does not
rotate properly, remove meat and remount for a proper balance.
8. Light grill per “Operating Infrared Back Burner” lighting instructions.
Note: Cooking grid can be removed if necessary.
9. Keep lid closed during cooking.
Replacing the batteries (See “Assembly Instructions – Rotisserie” Step 2)
1. Remove rotisserie box back cover.
2. Replace D batteries (2).
3. Replace rotisserie box back cover.
Operating Grill Lights
WWARNING: Install batteries correctly observing the +/- polarity signs.
WWARNING: Remove exhausted batteries and batteries not used for extended periods.
WWARNING: Store unused batteries in their pack, away from metal objects that may cause a short circuit.
WWARNING: Only recharge rechargeable batteries. Do not open or dispose of batteries in fire as they may explode.
WWARNING: Batteries should only be replaced by a responsible adult.
WWARNING: Do not mix old and new batteries
WWARNING: Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries
Turning On
1. Make sure the grill light button is in the (OFF) position (Figure 16).
2. Connect and secure battery box, per assembly instructions.
3. Push grill light button to (ON) position (Figure 17).
Turning Off
1. Push grill light button to (OFF) position (Figure 16).
2. Disconnect battery box cord.
Note: battery cord should always be unplugged when not in use.
Replacing the batteries (See Assembly Step 24)
1. Remove battery box back cover.
2. Replace AA batteries (4).
3. Replace battery box back cover.
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Before Each Use:
1. Keep the grill area clean and free from any combustible materials, gasoline, and other
flammable vapors and liquids.
2. Do NOT obstruct the flow of the combustion of LP gas and the ventilation of air.
3. Keep the ventilation opening(s) of the Gas cylinder area free and clear from debris.
4. Visually check the burner flames to make sure your grill is working properly (Figure 18).
5. See sections below for proper cleaning instructions.
6. Check for obstructions of airflow to the burners. Spiders, insects and webs can clog the
burner/venturi tube. A clogged burner tube can lead to a fire.
Cleaning Surfaces
1. Wipe surfaces clean with mild dishwashing detergent or baking soda mixed with water.
2. For stubborn surfaces, use a citrus-based degreaser and a nylon scrubbing brush.
3. Rinse clean with water.
4. Allow to air dry.
Cleaning Main Burners
1. Turn the regulator valve handle counterclockwise into the the “OFF” position (Figure C).
2. Turn all control knobs clockwise to the (OFF) position.
Note: A “poof” sound is normal as the last of the gas is burned.
3. Disconnect gas cylinder per “Disconnecting Gas Cylinder” section.
4. Remove cooking grids and heat plates.
5. Remove burners by removing the fasteners, which secure the burners to the grill bottom.
Loading...
Terms of Use | Privacy Policy | DMCA Policy
2006-2020 Rsmanuals.com